- 2-way bi-amplified, optimized Active loudspeaker system
- High-output precision titanium compression driver
- Neodymium long-throw low frequency transducer with 3-inch voice coil
- Servo Feedback controlled woofer for tight low-end punch
- 300W class-D, Fast Recovery LF amp / 100W HF amp
- Ultra-wide, smooth dispersion via multi-cell horn aperture and HF waveguide
- Built-in phase-accurate 24dB Linkwitz-Riley electronic crossover
- Mackie Active Electronic time alignment, phase correction and EQ for studio quality sound
- Mic/line input and pass-thru connector
- Lightweight for ultimate portability (40lbs)
- Flyable, Pole Mountable, Floor Wedge-able
|
| System Specifications | | | Frequency Response ) | (–3 dB | | | 55 Hz – 18 kHz | | Frequency Range | (–10 dB) | | | 4 5 Hz – 20 kHz | | Directivity Factor; | Q (DI) 9 .95 (9.98), averaged 2 kHz to 10 kHz Max SPL Long-term 1m | | | 124 dB | | Max SPL Peak 1m | 127 dB | | Crossover | Linkwitz-Riley, | | | 24 dB/octave 1600 Hz | | Audio | | | Input Type | Balanced Differential | | Input Impedance | 2 0 kohms | | Input Protection | RFI and level protected | | Sensitivity | | | Line | +4 dBu (center detent) | | Mic | –36 dBu | | Maximum Input Level | +22 dBu | | Low-Cut Frequency | 75 Hz, Second-order filter | | Acoustic Contour Equalization | | | Peaking | +3 dB 100 Hz, | | | +3 dB 12 kHz | | Operating Temperature Range | –10ºC to 45ºC (14ºF to 113ºF) | | Power Amplifiers | | | Low-Frequency Power Amplifier | | | Rated Power | 3 00 watts | | Rated THD | < 0.1% | | Cooling | Convection Extrusion | | High-Frequency Power Amplifier | | | Rated Power | 100 watts | | Rated THD | < 0.1% | | Cooling | Convection Extrusion | | Transducers | | | Low-Frequency Transducer | | | Diameter | 12 in/300 mm | | Voice Coil Diameter | 3 .0 in/75 mm | | Sensitivity | (1W1m) 9 8 dB | | Nominal Impedance | 8 ohms | | Power Handling | 600 watts, program | | Frequency Range | 4 5 Hz – 3 kHz | | High-Frequency Transducer | | | Diaphragm Diameter | 1.75 in/44 .5 mm | | Diaphragm Material | Heat treated titanium | | Sensitivity | (1W 1m) 106 dB | | Nominal Impedance | 8 ohms | | Power Handling | 100 watts, program | | Frequency Range | 1 kHz – 20 kHz | | Horn Design | | | Type | Conical and Exponential | | Mouth Size | 12 in/304.8 mm (W) x 7 in/177.8 mm (H) | | Throat Diameter | 1 in/25.4 mm | | Horizontal Coverage | 9 0º (1 kHz–20 kHz) | | Vertical Coverage | 4 5º (2.8 kHz–20 kHz) | | Line Input Power | | | US | 120 VAC, 60Hz | | Recommended amperage service | 2 .5 amps | | Europe | 23 0 VAC, 50Hz | | Recommended amperage service | 1.25 amps | | Japan | 100 VAC, 50/60Hz | | Recommended amperage service | 3 .0 amps | | AC Connector | 3 -pin IEC 250 VAC | | Control System Function | Electronic Crossover | | | Phase Alignment | | | Equalization | | | Parametric Equalization | | Safety Features | | | Over-Excursion Protection | Second-Order High-Pass Filter | | Thermal Protection | Amplifier shutdown, auto-reset | | Low-Line Voltage Shut Down | 60% Nominal line | | Driver Protection | Independent LF and HF compressors | | Low-Freq Roll-Off | Dynamic, signal-level dependent | | Construction Features | | | Material | Polypropylene | | Finish | Midnight Blue, textured finish | | Handles | One on each side, one on top | | Mounting Methods | Integrated mounting points, M10 two each located on each side, top, bottom, and two each located on each side, top, bottom, and rear of enclosure | | Grille | Perforated metal with weather-resistant coating | | Display | LEDs Signal Present, Peak, Power ON, and Thermal | | Physical Properties | | | Height | 2 6.0 in/660 mm | | Width | 15.4 in/39 0 mm | | Depth | 14.8 in/376 mm | | Weight | 4 0 lb/18 kg | |
|